ABSORBERS FOR TOURING MODELS
- Progressive Suspension
944 ULTRA TOURING: Specifically designed to deliver
a comfortable ride at a 1" lowered stance. Built around the latest FST technology,
The Ultra Touring shocks utilize all the suspension travel provided
by the full length units, but in a 1" lowered ride height.
The unique Ultra Touring spring combination not only delivers a
ride height while its being ridden, but also while it's on the
Part #: M29032 - Progressive Suspension 13" 944
Ultra Touring Pair with Heavy Duty Springs.
Fits FL & Touring models 5 speed 1980/Later ... $743.82
944 ULTRA LOW: Just like the name
implies, this is the lowest version of the 944 Series shocks. Designed
to sit 2" lower
than a stock HD Touring model and provide the best ride a short shock
your bike in the weeds or struggling to reach the ground? The 944
Ultra Low is the shock for the job.
Frequency Sensing Technology (FST) allows the shocks to sense the frequency
of a bump and automatically adjust damping for superior ride quality
Sits 1" lower on most models
Adjust spring pre-load by hand, no special tool needed
Progressive Rate Main Springs specifically designed for touring
Available in standard and heavy duty spring rates
Made in the USA
Note: There is no substitute for suspension travel. For optimum ride
quality we recommend the taller Ultra Touring version of the 944 Series
Part #: M29031 - Progressive Suspension
Ultra Low Pair with Standard Springs.
Fits FL & Touring models 5 speed 1980/Later ... $743.82
Part #: M29033 - Progressive Suspension 12.5" 944
Ultra Low Pair with Heavy Duty Springs. Fits FL & Touring modles
5 speed 1980/Later ... $743.82
Progressive 412 Series
BODY SHOCK ABSORBER SETS FOR BIG TWIN & SPORTSTER - Progressive
Multistage velocity sensitive internal valving, double walled steel bodies
and precision ground hardened steel shafts for fade free operation with
a consistent ride over a variety of surfaces and extended seal life.
Spring pre-load is easily set with a cam type adjuster.
Shock length is measured from center of eye to center of eye (always
verify existing shock length before ordering).
Includes a spring pre-load adjusting tool.
Instructions are included. Made in the U.S.A.
Note: When using shocks shorter than OEM, check
all related parts such as tire to fender clearance with shock fully
aim and Jiffy stand lean angle.
Rear Shocks for Softail 2000/L
and 1989/1999 - Progressive Suspension
controlled ride height (down to 2" lowered seat height) is easily
adjusted on the fly by the optional on-board compressor kit. (See below.)
The optional hand pump is an economical means of adding air pressure if
the on-board compressor kit is not desired.
One shock of the chrome plated set is conventional and incorporates a
coil spring and damper assembly. This shock basically supports the weight
of the motorcycle and controls the compression/rebound dampening characteristics.
The other shock features two separate air adjustable chambers. One chamber
is used for the rider/passenger's weight and the other is used to control
the ride height.
The advantage of the airtail system is that the air compresses at a progressive
rate and easily solves the age old problem of bottoming out (even when
running in the lowered state).
The on-board compressor kit includes a chrome plated coil cover that houses
an air pressure gauge, rocker switch for adding air to each chamber and
two push button air bleed valves. The air compressor itself mounts to
the rear fork axis tube and no modification is required to your existing
parts for installation. Instructions are included.
The hand pump is designed for people that won't be constantly changing
the ride height. You can just set it and forget it and enjoy a better
ride than was previously available from any other shocks available. Made
Shock set, Fits Softail 2000/Later. ... Price $668.60
Recommended On-Board Compressor Kit for Airtail Shocks
of the airtail system is that the air compresses at a progressive rate
and easily solves the age old problem of bottoming out (even when running
in the lowered state).
compressor kit includes a chrome plated coil cover that houses an air
pressure gauge, rocker switch for adding air to each chamber and two push
button air bleed valves. The air compressor itself mounts to the rear
fork axis tube and no modification is required to your existing parts
for installation. Instructions are included.
Made in USA.
LENGTH SHOCK ABSORBER SETS FOR SOFTAIL - Progressive Suspension
Lowers seat height as much as 2".
These 422 Series shocks are designed to provide the ultimate in ride quality.
Features Inertia Active System (I.A.S.) damping. This type of "state
of the art" valving senses the difference between chasis movement
and wheel movement. When the wheel encounters a pot hole or expansion
joint the damping changes instantly from firm to soft allowing the wheel
to move rather than having the jolt transmitted to the chassis and the
Progressive wound springs further enhance the ride quality by increasing
in tension relative to the amount of shock travel.
Nitrogen charged to help eliminate dampening fade unde extreme conditions
and high heat.
Large windows in the shock covers provide a unique look while eliminating
3/8" drive tool is included for spring tension and ride height adjustment.
Instructions and Tool are included. Note: FLSTN models have a 1" lowered ride height from the factory
so these shocks must be adjusted accordingly. When reducing ride height,
always check headlight aim and correct lean angel on jiffy stand.
SUSPENSION DROP KITS FOR BIG TWIN TOURING, SOFTAIL, DYNA & SPORTSTER
- Burly Brand
Go from stock to slammed in about an hour!
The Slammer is a complete lowering kit in one box.
No disassembly of forks required, they can stay on the bike while you work!
No special tools needed for installation.
The shocks included in the kit lower the rear up to 2 1/2" and the
fork springs lower the front up to 2".
Kit includes two 10 1/2" shock absorbers, two Slammer fork springs,
two helper springs, two spring spacers, one spanner wrench, one lube
packet, and complete installation instructions.
Made in the U.S.A.
FORK LOWERING KITS FOR SOFTAIL - Progressive Suspension
These kits are designed to be used with OEM rear shocks to lower a Softail
model motorcycle as much at 2" depending on the kit used. Kits are
chrome plated. After the shocks are removed from the bike, installing
kit can be done by using a shop press. Installation instructions are
- Chrome plated adjustable kit. OE height to 2" lower.
Includes rubber bumpers and cup washers. Fits Softail 2000/Later. ...
what you need?Contact us.
Chances are we have it. We have thousands of parts that are not
NOTE: We Do NOT Backorder. If your
item is not in stock, you will be notified and given a refund.
RATE SHIPPING APPLIES IN CONTINTENTAL
48 UNITED STATES ONLY. AK, HI and APO/FPO will have additional
shipping fees. We ship within the U.S.A. and
to APO/FPO (military addresses; weight and size restrictions apply.).
We do not accept foreign credit cards. Please see our CONTACT
page for more information.
to call in your order to Steel Thunder? Call 603-237-8200.