FLAT RATE SHIPPING!  No hidden fees and NO TAX! Only $12.95 in the continental. U.S., no matter how large (or heavy) your order is!  Save $$$ ... order everything you need NOW! 

No special club to join... just great low prices every day.
HOME
CONTACT
SITEMAP
SPORTSTER

Twin Cam Tools

Due to the racidcal new design of the Twin Cam, specialized tools are required to properly perform engine repair without damage. All JIMS tools are manufactured from top quality material and designed for years of trouble free service. All tools include instructions. Made in the U.S.A.

Jims cam chaIN TENSIONER TOOL FOR TWIN CAM, MADE IN AMERICA.

Cam Chain Tensioner Tool - Jims

Tool will unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams and can also check spring loads on chain tensioners.
Replaces HD# 42313
Part#: 60827 ... $52.76

Jims camsahft/crakshaft locking tool for twin cam motorcycles.  Made in the U.S.A.


Camshaft/Crankshaft Locking Tool - Jims

Precision tool allows the technician to lock the camshaft and crankshaft sprockets to properly remove, replace and torque the sprocket bolts. Tool is made from non-marring delrin.
Replaces HD# 42314
Part #: 60831 - Fits Twin Cam 1999/2006 (except 2006 Dyna) ... $55.22

Part #: 60810 - Fits Twin Cam 2007/Later & Dyna 2006/Later... $79.56

JIms camshaft remover and installation tool for twin cam motorcycles.

Camshaft Remover & Installation Tool - Jims

Multifunction tool will remove and replace front and rear camshafts and the ball bearings. It provides the precision alignment of the camshaft to insure a smooth press in and out of the support plate.
Replaces HD# 43644
Part #: 60829 ... $193.80

JIms cam bearing installation tool for twin cam motorcycles.

Collar only for twin cam  bearing installation.

 

Cam Bearing Installation Tool - Jims

Tool will install the two inner cam needle bearings into the crankcase. It perfectly aligns to the shaft bores for a precision press fit.

Part #: 60830 - Fits All Twin Cams ... $205.50

Part #: 60807 - Collar Only fits all Twin Cam ... $76.81

Jims cam assembly tool for twin cam motorcycles.

Cam Assembly Tool - Jims

Use this tool to hold both cams in an upright position while lowering the cam support plate over both guides and cam journal guides. Tool has been manufactured from a non-marring material, that will not damage any of the cam's surfaces. Use on all Twin Cam 2007/Later & Dyna 2006/Later.
Part #: 60809 ... $184.46

Jims innner cam bearing remover for twin cam motorcycles.  Made in the U.S.A.

Inner Cam Bearing Remover - Jims

Blind hole puller will easily remove the crankcase needle bearing that supports the camshafts. The unique design prevents the pin rollers from accidentally falling into the crankcase that is known to happen when using inferior pullers.

Part #: 60828 Fits Twin Cam 2000/2006 (except 2006 Dyna) ... $176.93

Part #: 60808 Fits Twin Cam 2007/Later & Dyna 2006/Later ... $277.90

Secured by SSL - an authentic COMOCO site.

Don't see what you need?  Contact us.  Chances are we have it.  We have thousands of parts that are not shown online.

PLEASE NOTE: We Do NOT Backorder. If your item is not in stock, you will be notified and given a refund.

We ship within the U.S.A. and to APO/FPO (military addresses; weight and size restrictions apply.). We do not accept foreign credit cards. Please see our CONTACT page for more information.

 

FREQUENTLY ASKED QUESTIONS

Please note that all prices are subject to change.

***

Steel Thunder Custom Cycles

531 Bungy Road

Columbia, NH 03576

Copyright 2002-2017 Steel Thunder Custom Cycles©

 

Thank you for shopping at Steel Thunder Custom Cycles online motorcycle parts store!

All-Over-Print

Protected by Copyscape Duplicate Content Detection Software

 American Made Leathers to Last a Lifetime! FoxCreekLeather.com

Free Shipping! Necklaces, Earrings, Bracelets, Rings, Brooches, etc at SammyDress.com! 

Motorcycle Eyewear